U-Joint Puller for Trucks - 10104, 10102, 10100

Mid Size - 10104: For Intermediate (Class 4, 5, 6)  |  Heavy Duty - 10102: For Heavy Duty (Class 7, 8)  |  Hydraulic Puller - 10100: For Heavy Duty (Class 7, 8)

Made in Canada

Mid Size - 10104

$ 189.99


Heavy Duty - 10102

$ 261.99

Optional:



Hydraulic Heavy Duty - 10100

$ 2,026.38

Discontiued



With brute strenght provided by a U-joint Puller. It can dissassemble even the most seized U-joints in minutes.

Features

  • Original U-Joint Puller!
  • Engineered for use w/up to a 1" impact tool. (10102)
  • Can be used on aluminum driveshaft. (10105)
  • Eliminates dangerous vice & socket or hammering methods. (10102/10104/10105)
  • Does not damage the driveshaft, yokes, joints or bearing cups. (10102/10104/10105)
  • One piece unit – No bolts, cables, or assembly required. (10102/10104/10105)
  • 10104 Intermediate U-Joint Puller will works on:
    • All intermediate trucks w/ a bearing cup diameter of 1.25" to 1.7"
    • Spicer SPL 90 & 100 Series Drivelines
  • 10102 Heavy Duty U-Joint Puller will works on:
    • Designed to work on virtually all Class 7 and 8 trucks and machinery where the bearing cup outside diameter is 1.5" to 2.2".
  • 10100 - Hydraulic Heavy Duty U-Joint Puller
    • Original and World's Greates U-joint Puller
    • Pulling Power: 20 Tons
    • Ideal for the driver w/ air supply limitation
    • Prevent damages of yokes, driveshaft, bearing cups or joints.
    • Requires 10,000 PSI hydraulic pump.
  • Warranty
    • Life time warranty on cast parts, 2 year warranty on threaded parts, all depending on misuse.

Note: Hammering this tools will void your warranty.

Application for Mid Size U-Joint 10104

  • U-Joints with bearing cups 1.25" to 1.7" O.D.
  • Spicer SPL 90 & 100 Series
  • Not compatible with: Double cardan joints
  • Applicable for:
    • Automotive Vehicles
    • Intermediate Vehicles

Note: Do not use over 1/2" impact wrench. Doing so will void warranty.

Application for Heavy Duty U-Joint 10102

  • U-Joints with bearing cups 1.5" to 2.2" O.D.
  • Spicer 1610, 1710, 1760, 1810, 1880 Series
  • Spicer SPL 140, 170, & 250 Life Series
  • Meritor (Rockwell) 16N, 17N, 18N, 1710 Series
  • Meritor RPL 20, 25 Permalube Series
  • Applicable for Heavy Duty Vehicle
  • Optional Parts

Application for Hydraulic Heavy Duty U-Joint Puller 10100

  • U-joints with bearing cups 1.5" to 2.2" O.D.
  • Spicer 1610, 1710, 1760, 1810, 1880 Series
  • Spicer SPL 140, 170 & 250 Life Series
  • Meritor (Rockwell) 16N, 17N, 18N, 1710 Series
  • Meritor RPL 20, 25 Permalube Series

10104 - Intermediate U-Joint Puller Operating Instructions

  1. Remove all bolt retainers from bearing cups.
  2. Slip the U-Joint Puller over the yoke of the driveline.
  3. Turn the tool’s forcing screw clockwise with either an air or hand wrench. (Note: reverse thread)
  4. Once the bearing cup is free, rotate driveshaft and remove the opposing bearing cup. Remove the remaining two bearing cups using the same method.

10102 - Heavy Duty U-Joint Puller Operating Instructions

  1. Remove all fasteners from bearing cups
  2. Slip the U-Joint Puller over the yoke of the drive line.
  3. Turn the tool’s forcing screw clockwise with up to a1 impact wrench.

Application for Hydraulic Heavy Duty U-Joint 10100

  • Spicer 1610, 1710, 1760, 1810, 1880 Series
  • U-joints w/ bearing cups 1.5" to 2.2" O.D.
  • Meritor (Rockwell) 16N, 17N, 18N, 1710 Series
  • Spicer SPL 140, 170 & 250 Life Series
  • Meritor RPL 20, 25 Permalube Series

Note: Reverse threads, bottoming out forcing screw on frame may cause unwarrantable damage to threads.

Note: Failure to check the spherical thrust washer and replace as necessary may result in un-repairable damage to your u-joint puller glove casting. Preventative maintenance as outlined below will ensure many years of use from your tiger tool puller. Failure to perform preventative maintenance will void warranty.

Preventative Maintenance U-Joint 10104

Keep forcing screw clean and lubricated at all times. Lubricate load bearing surface in glove and under cap. We recommend SAE 30 lube for the threads and EP molly grease.

Preventative Maintenance U-Joint 10102

Keep forcing screw clean and lubricated at all times. Failure to maintain the spherical thrust washer located inside the glove (Item 2) will result in excessive wear to the glove. Check and lubricate this part (lubricate load bearing surface in glove, under cap, on both sides of spherical washer) periodically and replace as necessary. Contact your Dealer or Tiger Tool for replacement washers.

Warranty Policy

Tiger Tool International Incorporated (“Tiger Tool”) warrants to its customers that cast portions of its tools are free from defects in workmanship and materials for as long as the original purchaser owns the tool.

Tiger Tool warrants to its customers that threaded areas, bolts and machined components in or of its tools will not fail due to defects in workmanship and materials for a warranty period of two years from the date of original purchase.

Tiger Tool warrants to its customers that hydraulic components will not fail due to defects in workmanship and materials for a warranty period of one year from the date of original purchase.

For warranty service a customer must return the tool freight prepaid along with original proof of purchase to TIGER TOOL INTERNATIONAL INCORPORATED.

When a customer seeks warranty service with respect to a tool and that tool is covered by a TIGER TOOL warranty, TIGER TOOL may at its option repair the tool, replace the tool or refund the purchase price for the tool.

New unused product that is returned to tiger tool as a result of the customers error or due to inventory adjustment will be subject to a twenty percent (20%) restock/rework fee with authorized RGA number otherwise a 30% restocking fee will apply.

See Tiger Tools Limitations of Liability


Back to Top
U-Joint & Clutch
Mechanic Tools



Highly Recommended